Comments

• 

  mahsa May 21, 2019 at 3:23am

  hi, i want to transfer my rhino file in to sap2000 v20,and i'm new to sap.i found out that i should use the geometry gym plugin.so i downloaded [ggRhino6SAP20 v1.4.04.msi (31st March 2019) v20].it didn't ask me for any license during the installation.but now when i want to use the command,it says as an unknown command.what should i do?

  thx
• 

  sonia ruta May 14, 2019 at 9:20am

  Dear Jon,

  after repairing ggRhino6Karamba1.3.1 , it shows "1. Solution exception:Unlicensed!!! To activate full functionality please request a trial license by running command ggKarambaZZLicenseRequest
  Run Rhino command ggKarambaZZLicenseRequest or contact Jon!"

  Could you please help me to solve it? it is a little bit urgent  I'm doing my Thesis project with it...many thanks!

  Sonia
• 

  Tina Irvine February 6, 2019 at 10:53am

  Hi Jon, 

  I'm trying to use the ggstage in Grasshopper to get the relevant stages into GSA.

  However, it doesn't seem to like the active elements I'm inputting. I keep getting the error message '1. Solution exception:Object reference not set to an instance of an object.' Is there a trick to getting this to work? I also can't fed the ggStageProp into GSA either?

  Can you help? 

  Tina
• 

  foodove August 9, 2018 at 12:58pm

  sry~and my email is foodove@gmail.com, ty~
• 

  foodove August 9, 2018 at 11:54am

  Dear Jon,

  after repairing ggRhino5Karamba1.3.0 v0.1.10, it shows "1. Solution exception: Unlicensed!!! To activate full functionality please request a trial license by running command ggKarambaZZLicenseRequest
  Run Rhino command ggKarambaZZLicenseRequest or contact Jon!", I ran Rhino command ggKarambaZZLicenseRequest but it doesn't work. Could you please help me to solve it? it is a little bit urgent bc I'm doing my Thesis project with it...many thanks!

  Allbest,

  Dove
• 

  Scabinus February 16, 2018 at 10:01am

  Dear Jon,
  I find your ggmeshtobrep command in rhino very usefull, why you did not develop it for
  gh?
  Thanks
• 

  Omid Karami June 23, 2017 at 8:52am

  Hi jon

  I downloaded your Geometry gym Plug-in, unfortunately it does not work because its license expire. How should I do? And I have one more question: How does gtt Plug-in work?

  My email address is: Eng.karami@gmail.com

  Yours Sincerely

  Omid
• 

  Sebastien de Wit October 20, 2016 at 12:27pm

  Dear Jon,

  I have some serious troubles getting the surface properly meshed with equal lengths, prior to the form finding part. Perhaps Kangaroo itself is able to do this? Hope you can help because meshing odd surfaces instead of rectangular shapes is not often shown on the forum.

  Yours sincerely,

  Curved%20Model%20%28positive%20Gaussian%20curv.%29.gh

   
• 

  shahryar July 18, 2014 at 3:42am

  Dear Jon,

  I am trying to import one gbXML file which was exported by Revit .I have  loaded it in Ecotect to apply material. Now, I am planning to import in Rhino to analysis in grasshopper. I have downloaded geometrygym plugin but it does not work in Rhino and just appears in grasshopper. Would you please guide and help me by offering any information how I can to import gbXML files to Rhino.

  Yours sincerely,
• 

  Gabriel Áh August 27, 2013 at 10:41am

  hey Jon, 

   Im trying to use geo gym, but this legend pops out:

  

  where can i get the free evaluation code and then extend it to the educational version

  by the way thanks for sharing, and congrats for the hard work

  best,

  gabriel